低阶煤颗粒-气/油泡间的诱导时间研究

为表征低阶煤颗粒-气/油泡间矿化过程的差异,通过Sutherland理论下固体颗粒进入泡沫产品的总概率(E)和浮选速率常数(k)之间关系,并结合低阶煤颗粒-气/油泡的浮选速率试验,求得了低阶煤颗粒-气/油泡间的诱导时间。浮选实验研究表明,在相同的捕收剂消耗量下低阶煤-油泡浮选产率均高于低阶煤-气泡浮选产率。诱导时间测试表明,低阶煤颗粒-油泡间的诱导时间(35 ms)要明显低于低阶煤颗粒-气泡间的诱导时间(93 ms)。上述实验结果表明,油泡表面的疏水性要强于传统浮选气泡表面的疏水性。然而,进一步利用Sutherland理论中固体颗粒进入泡沫产品的总概率和浮选速率常数之间的数学关系,并结合低阶煤颗粒-气/油泡的浮选速率试验求得的低阶煤颗粒-气/油泡间的诱导时间分别为9.67和8.46 ms,其与诱导时间测试仪分别测量的诱导时间差异很大。这主要是由于在实际浮选过程中气/油泡的上升速度分别为23.26和22.68 cm/s,其远高于2015EZ型诱导时间仪测试过程中气/油泡碰撞速度(2.0 cm/s)。因此,诱导时间理论计算表明气泡-颗粒间的碰撞速度对颗粒-气泡间的诱导时间影响很大。上述研究结果表明油泡浮选效果优于传统浮选的内在原因在于低阶煤颗粒-油泡间的诱导时间小于低阶煤颗粒-气泡间的诱导时间。     

Discrete element method study on hopper discharge behaviors of binary mixtures of nonspherical particles

This study is aimed at unveiling the influence of binary mixtures of nonspherical particles on hopper discharge behavior, which remains poorly understood. The discrete element method (DEM) is employed to simulate seven particle types with aspect ratios between 0 and 2 (namely, a sphere, two ellipsoids, two cylinders, and two cuboids) with the same volume. Seven monodisperse systems and twelve binary-shape mixtures are assessed. For the monodisperse systems, particle shape is the dominant factor dictating discharge rate, compared to other factors like aspect ratio, preferential orientation, and packing. Regarding the binary-shape mixtures, the discharge rates are similar for all twelve mixtures, reflecting a surprising lack of shape effects, which in turn means the negligible impact of solid volume fraction, aspect ratio, and segregation extent. Moreover, collision force is generally negatively correlated with discharge rate.     

复杂流道结构料仓的下料流率预测

在实验室搭建的有机玻璃料仓下料平台上，分别以自由流动粉体玻璃微珠和黏附性粉体煤粉和聚氯乙烯为实验介质，针对无改流体(No-In)、封闭改流体(Con-In)和开放改流体(Ucon-In)三种情况所形成的不同流道结构，开展了粉体料仓下料及其流率建模研究，定量分析了改流体对粉体下料流率的促进作用，对比给出了玻璃微珠、煤粉和聚氯乙烯在不同流道结构料仓内的下料特性。研究表明，改流体的引入有利于提高料仓下料流率，Con-In促进流动效果最明显，对于流动性弱的煤粉，下料流率提升幅度达到最大的58%。基于剪切摩擦区的概念，提出流率校正因子F对最小能量理论方程进行了修正，将理想的料仓下料模型拓展至实际下料过程。进一步，对于Con-In，根据流道结构特征结合对粉体的受力分析，修正了模型中的锥角项；对于Ucon-In，基于粉体下料流动竞争机制，提出分阶段下料模式并关联了内层和夹层的下料流率，最终建立了复杂流道结构料仓的下料流率预测模型。该模型综合考虑了粉体物性、下料流型和流道结构的影响，可有效预测自由流动粉体和黏附性粉体流经传统料仓(No-In)和改流体料仓(包括Con-In和Ucon-In)的粉体下料流率，且预测偏差<10%。     

月柿提取物体外抗氧化活性研究

目的以月柿提取物为原料,研究其对2,2-联苯基-1-苦基肼基(1,1-diphenyl-2-picrylhydrazyl,DPPH)自由基的清除能力,并测定其多酚类物质没食子酸的含量。方法检测波长为518 nm,反应时间为40 min条件下,以IC_(50)值(清除率为50%时,抗氧化剂的浓度值)作为抗氧化能力评价指标,并采用高效液相色谱法测定其没食子酸含量。结果月柿提取物对于DPPH自由基有良好的清除作用,其IC50值为0.1868 mg/mL,与常用抗氧化剂作用相当,且月柿提取物中没食子酸含量为1.65 g/kg。结论月柿提取物具有很强抗氧化活性,作为化妆品及功能性食品原料有广阔的开发前景。     

煤粉锅炉脱硫系统中除尘器压差过高原因及解决方案

高倍率灰钙循环烟气脱硫技术在神东矿区的煤粉锅炉环保改造项目中已投入建设并成功运行,脱硫率可达95%以上。在NGD系统的运行调试期,布袋除尘器压差的数值及其上升速度均较改造前有大幅提高,影响了锅炉系统的正常运行并降低了布袋除尘器的运行效率。为了解决此问题,先分析滤料透气性降低而导致布袋除尘器压差上升的根本原因,再结合现场调研情况对NGD系统工况下的烟气含湿量、烟气温度、烟气灰浓度、除尘器本体的问题以及上游锅炉系统问题逐一进行对比和分析,并找出问题产生的各主要因素。NGD系统中布袋除尘器差压升高的原因包括多方面,为了使NGD系统的运行更加稳定,需要使除尘器适应NGD系统的工况并对系统中部分设备进行改造。在未来NGD系统的设计中,布袋除尘器需按高浓度烟气设计,且针对煤粉工业锅炉的运行、维护特性应加入对烟气中含水量的监测及对布袋除尘器的相应保护措施。     

Ultrasonic-vibration-assisted laser annealing of fluorine-doped tin oxide thin films for improving optical and electrical properties: Overlapping rate optimization

An ultrasonic-vibration-assisted laser annealing method was developed to enhance the performance of fluorine-doped tin oxide (FTO) thin films. The influences of ultrasonic vibration, laser scan line overlapping rate (L_OR) and laser spot overlapping rate (S_OR) on surface morphology, FTO layer thickness, RMS roughness, crystal structure and photoelectric properties of the FTO films were investigated. The results indicated that the presence of ultrasonic vibration during laser annealing could significantly enhance the film compactness, and using moderate L_OR and S_OR values resulted in significantly decreased FTO layer thicknesses and RMS roughnesses as well as slightly increased crystallite sizes, thus yielding significantly improved optical transmittance values and slightly enhanced electrical conductivity values. It was found that the optimal L_OR and S_OR values for ultrasonic-vibration-assisted laser annealing of the FTO films were 80% and 90%, respectively. The as-obtained film possessed the best overall photoelectric property with an average transmittance (400–800?nm) of 85.9%, a sheet resistance of 8.7?Ω/sq and a figure of merit of 2.51?×?10^–2 Ω^–1. This work may be of great significance in terms of performance optimization of transparent conducting oxide (TCO) thin films.     

Tribological behaviour of a 3Y-TZP/Ta ceramic-metal biocomposite against ultrahigh molecular weight polyethylene (UHMWPE)

This study aims to evaluate the tribological behaviour of 3Y-TZP/Ta (20 vol%) ceramic-metal composites and 3Y-TZP monolithic ceramic prepared by spark plasma sintering (SPS) against ultrahigh molecular weight polyethylene (UHMWPE). According to the results of pin (UHMWPE)-on-flat wear test under dry conditions, the UHMWPE – 3Y-TZP/Ta system exhibited lower volume loss and friction coefficient than the UHMWPE – monolithic ceramic combination due to the presence of an autolubricating layer that provides sufficient lubrication for reducing the friction. Owing to the lubrication of the liquid media, under wet conditions obtained using simulated body fluid (SBF), similar behaviour is observed in both cases. Additionally, the ceramic and biocomposite materials were subjected to a low temperature degradation (LTD) process (often referred to as “ageing”) to evaluate the changes in the tribological behaviour after this treatment. In this particular case, the wear properties of the UHMWPE-biocomposite system were found to be less influenced by ageing in contrast to the case of the UHMWPE-zirconia monolithic material. In addition to their exceptional mechanical performance, 3Y-TZP/Ta composites also showed high resistance to low temperature degradation and good tribological properties, making them promising candidates for biomedical applications, especially for orthopaedic implants.     

Research on the identification performance of UHF RFID system considering the correlation of cascaded channel

The identification rate of UHF RFID system was restricted by multipath propagation effects.The system identification performance was studied considering the correlation coefficient between forward and reverse channels.Based on the generalized Rician fading channel model,the analytical expression of identification rate was derived under independent,full correlation and correlation cases.Compared with the existing analysis,the proposed uniform calculation formula of identification rate was for any correlation coefficient and kinds of channel conditions.The numerical computation and Monte-carlo simulations show that the influences of different correlation coefficients,channel conditions,sensitivity and distance on the identification rate.     

Group sequential crossover trial designs with strong control of the familywise error rate

Crossover designs are an extremely useful tool to investigators, and group sequential methods have proven highly proficient at improving the efficiency of parallel group trials. Yet, group sequential methods and crossover designs have rarely been paired together. One possible explanation for this could be the absence of a formal proof of how to strongly control the familywise error rate in the case when multiple comparisons will be made. Here, we provide this proof, valid for any number of initial experimental treatments and any number of stages, when results are analyzed using a linear mixed model. We then establish formulae for the expected sample size and expected number of observations of such a trial, given any choice of stopping boundaries. Finally, utilizing the four-treatment, four-period TOMADO trial as an example, we demonstrate that group sequential methods in this setting could have reduced the trials expected number of observations under the global null hypothesis by over 33%.